女生自慰网站,91乱伦中文字幕乱伦,亚洲五月婷婷,午夜爱爱爱爱

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

synchronous hydraulic cylinder Sold to Norway

Release time:2023-11-09 08:46:38 Hits: Current position: Home > News

This article mainly introduces:

Norway hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

Norway synchronous hydraulic cylinder

(Norway synchronous hydraulic cylinder,produced by Hengyu Group)

synchronous hydraulic cylinder are widely used in Norway,because of powerful torque,clever hydraulic energy conversion,simple structure and reliable operation.So our company has designed synchronous hydraulic cylinder for customers from Norway.

Introduction to synchronous hydraulic cylinder:

There are some honeycomb holes in the inner wall of the synchronous hydraulic cylinder, piston or piston rod surface. How is this formed? When we repair the synchronous hydraulic cylinder, we can see that there are some honeycomb holes on the inner wall of the synchronous hydraulic cylinder, the piston or the piston rod surface, which are caused by cavitation. Therefore, the cavitation of the synchronous hydraulic cylinder is targeted to prevent. Is very necessary.

synchronous hydraulic cylinder seal leakage causes and countermeasures: a. Loose tie rod nut will cause leakage, tighten the tie rod nut according to the torque requirements of tie rod nut, test no leakage can continue to use. b. Pressure exceeding the limit will also cause leakage. Replace the synchronous hydraulic cylinder seal and re-tighten the tie rod nut to reduce the pressure to the nominal pressure range of the synchronous hydraulic cylinder. c. The synchronous hydraulic cylinder seal is extruded, if the O-ring is obviously extruded at the synchronous hydraulic cylinder seal, replace the synchronous hydraulic cylinder seal.

When the oil pressure of the synchronous hydraulic cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

When the synchronous hydraulic cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the synchronous hydraulic cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the synchronous hydraulic cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

Answers to some questions about synchronous hydraulic cylinder:

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.

Two cylinders in parallel, how to solve the synchronization problem?
The following methods can be used to achieve parallel cylinder synchronization: 1, rigid mechanical synchronization. 2. The throttle valve or speed regulating valve is used in the circuit to adjust the synchronization. 3, the two cylinders use independent quantitative pump oil supply to achieve synchronization. 4. Synchronous motor is used in the loop to realize cylinder synchronization. 5, using the position sensor to measure the stroke position and control the cylinder synchronization through the electrical system.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
精品一二三| 波多野结衣绝顶大高潮| 日本久中文| 日本道高清激情在线观看| 可以直接在线看的视频你懂的| 久久久厕所| 波多野结衣乳巨码无在线| 越西县| 国产乱码精品一区二三赶尸艳谈| 97久久久久| 中文字幕 日韩 在线| 亚洲激情av| 色鬼久色| 福利在线| 91麻豆国产| 九色综合婷婷| 久久免视频线观看| 亚洲AV无码专区国产乱码4SE | 久久无码国产专区精品| 999久久久久久久久6666| 国产免费av片在线无码免费看| 国模国产精品嫩模大尺度视频| 婷婷综合高清无码| 国产欧美另类久久久精品图片| 久久国色夜色精品国产| 五月天综合| 琪琪在线视频| 欧美乱码精品一区二| 日韩福利电影无码| 免费AV操| 涩涩鲁亚洲精品一区二区| 国产一区二区加勒比| 国产精品调教| 日韩做不卡视频| 欧美日韩国产一区| 丝袜人妻XXX网| 日韩精品一欧美精品| 亚洲色无码精品一区二区| 香蕉视频草莓视频| 国产伦精品一区二区三区男技| 日韩av一级|