女生自慰网站,91乱伦中文字幕乱伦,亚洲五月婷婷,午夜爱爱爱爱

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

200 ton hydraulic cylinder Sold to UAE

Release time:2023-11-20 09:49:55 Hits: Current position: Home > News

This article mainly introduces:

UAE hydraulic cylinder,200 ton hydraulic cylinder manufacturer,200 ton hydraulic cylinder

UAE 200 ton hydraulic cylinder

(UAE 200 ton hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

200 ton hydraulic cylinder are widely used in UAE,because of no need for deceleration device,long service life,smooth movement.So our company has designed 200 ton hydraulic cylinder for customers from UAE.

Introduction to 200 ton hydraulic cylinder:

In the process of using the 200 ton hydraulic cylinder, sometimes such a problem will occur, the 200 ton hydraulic cylinder can not act immediately after the instruction of the 200 ton hydraulic cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil 200 ton hydraulic cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

When purchasing the 200 ton hydraulic cylinder, try to clarify the following parameters of the 200 ton hydraulic cylinder: A. 200 ton hydraulic cylinder diameter, rod diameter, stroke; B. Working pressure or 200 ton hydraulic cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right 200 ton hydraulic cylinder type can be found accurately and quickly.

If the piston rod and 200 ton hydraulic cylinder are stuck or the 200 ton hydraulic cylinder is blocked, at this time, no matter how to operate, the 200 ton hydraulic cylinder does not move or has little action. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the 200 ton hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

When the 200 ton hydraulic cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the 200 ton hydraulic cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil 200 ton hydraulic cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical 200 ton hydraulic cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the 200 ton hydraulic cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

Answers to some questions about 200 ton hydraulic cylinder:

PLC+ inverter + motor + pump + solenoid valve + cylinder combination, can control the accuracy of cylinder position?
In the case of extremely high accuracy requirements, you can not, please consider a few problems: 1, hydraulic oil can be compressed, it is elastic like a spring. Therefore, in the general hydraulic servo system, the valve control is far more accurate than the pump control. Because the valve can be installed very close to the hydraulic cylinder, or even installed on the hydraulic cylinder, but the pump must go through the tubing and then into the hydraulic cylinder, there is a long distance, which greatly reduces the rigidity of the system and increases the difficulty of control. 2, the quantitative pump is first of all leaking, and there is 10%-20% flow pulsation. Secondly, and more unfortunately, the leakage of the pump is related to the pressure and is non-linear.

Slide weight 35 kg exit stroke 55mm, is it suitable to use 40 cylinder diameter cylinder?
The maximum output force of the 40-bore hydraulic cylinder can reach 2 tons, and whether it can be used depends on the use scenario. In addition, the problem of mechanism stuck has nothing to do with the size of the power source, and reasonable structural design and good machining and assembly accuracy are the key.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
亚洲日本va一区二区三区| 少妇裸体性猛交视频| 国产精品视频七区| 永和县| 性色av无码爆乳一区二区| 无码人妻少妇色欲AV一区二区 | 国产人产一区二区三区红桃影视| AV在线影视| 亚洲精品无码老司机带带我高| 少妇| 久久合综| 777午夜伦理影院| 激情久久丁香| 亚洲青青草| 成人国产成人在线观看视频| 亚州,日韩,欧美变态另类一区| www.插.com| 中文字幕 日韩精品 高清无码| 欧美一级特黄aaaa片尤果网| 华安县| 久久香色| 伊人久久大香线蕉av超碰| 色视频一区二区三区| 老太婆交性欧美| 甘德县| 久久一区二区三区精华液介绍 | 欧美日韩在线| 91久久国产最好的精华液| 国产91精品熟女动漫| —道日本dVd欧美| 久久精品国产精品久久| 熟女精品69导航| 色综合色五月| 国产免费无码一区二区视频| 一区二区三区成人电影| 久久九九国产| 久久偷拍精品视频| 久久精品系列| av电影手机在线观看网站| 久久国产午夜 AV| 亚洲日韩精品国产一区二区三区|